July 15, 2022

Sophie Radich: Large-scale timber construction

Sophie Radich: Large-scale timber construction

Large-scale Norwegian construction project in mass timber

The leading Norwegian project developer and contractor, Kruse Smith, is currently building a new school in mass timber of which the majority consists of CLT elements. Kruse Smith has chosen to use Woodsense wireless moisture sensor in the mass timber construction to gain knowledge and experience for future construction projects:

“We have placed the sensors in exposed areas where we knew there was an increased risk of moisture based on the physique of the building and that condensation can also form in the construction,” says Raymon Finstad, project engineer at Kruse Smith.

The sensors are placed against the edge of the roof to ensure proper roofing, under windows on roofs, and on various facades to monitor the difference in facadas that are facing north, south, east and west.

“Woodsense sensors have been very manageable. It has given us more control with the construction, and the opportunity to monitor the moisture content in both the timber construction and throughout the construction as a whole. We have placed sensors evenly throughout the construction and have received good feedback from roofers who are experiencing a higher sense of control. The developers are very satisfied with us testing the product, which has also given us a better sense of control,” explains Raymond Finstad.

Sensor detected fault with roofing

A sensor was placed on a cornice to keep an eye on the cover towards the edge. Here, the sensor found a mistake made by the roofer which the developer was notified of by the intelligent moisture alarm:

“The damage that occurred was on the cornice, where we had chosen to place a sensor. Water entered the construction due to the roofer not having completed the covering, which resulted in the moisture rising to more than 30 %, and we consequently got an alarm from the sensor. When we opened, we managed to decrease the moisture level to 22 %. So this is the sensor we are currently monitoring,” says Raymond Finstad.

Raymond Finstad explains that by having the sensors placed after the damage, they are able to see that the moisture level has not stopped at 22 % and is not trying out further. This provides them with useful information that they will have to take further action to further decrease the moisture level.

Moisture sensor on mass timber
Wireless moisture sensor placed on timber element, Sophie Radich, 2021.

Several sensors will now remain on the roof, so that the developer can subsequently ensure that the green roof laid on top lasts as expected, and that the drain likewise works as intended.

“Had we not had the sensor placed, we would not have found the moisture,” says Raymond Finstad.

Had the sensor not found the damage on the cornice, it would have led to a much more extensive repair. The contractor will therefore recommend all roofers to use the sensors in their own quality assurance and resell the advantage that the sensor gives the developer, Daniel Nilstun, construction manager at Kruse Smith, explains:

“We have received positive feedback from the developers on the placement of the sensors in the construction because we can see that we have a better control of the moisture throughout the construction.”

Potential in moisture measurement with sensor

Elsewhere on the construction site, a sensor was placed where a tarp was used to keep water from entering while they awaited extra material to cover the area. Through the sensor, they have discovered that water did enter the construction, which has created transparency among construction actors about when and how much water the areas have been exposed to.

Moisture sensor on large scale timber construction
Window solutions at facade, Sophie Radich, 2021

Had Kruse Smith involved Woodsense earlier in the construction, they would also, among other things, have placed sensors at a window solution where the developer had concerns. The window solution had been pushed out from the outer wall, and there had been discussions about where the condensation could be expected. Daniel Nilstun also sees great potential in the sensor when it comes to proving discussions on building physics:

“The industry builds a great deal, although we actually have very little knowledge. Ever since the advent of the vapor barrier, there have been many challenges. Here, a tool like the one from Woodsense can be incredibly useful in addition to the valuable in capturing potential damages through changes in the wood moisture content both continuously and after the construction has been put into use.”

With the sensors, it is possible to measure the moisture content in wood, keep an eye on particularly exposed risk areas and thus take a preventative approach to potential damages both on construction site and maintenance. Therefore, the moisture sensor is recommended for actors in the construction industry when documenting correct moisture management.

Could also be of interest